Those white chunky-heeled boots, how I loved them! I loved them from 2013 through early 2019,
and I wanted to love them even longer, but, like all synthetic
leathers, they began to lose their thin outer layer of plastic in a
manner most flaky. But still, they were my most flattering pair of
boots, and I couldn't bear to give up on them.
Resfashion to the rescue! Like the equally beloved pair of white pumps
before them, I thought to disguise their scruffy exteriors with a fresh
coating of fabric.
I planned to use some sheer floral chiffon from my
stash—the remains of my tiered sundress-turned-coverup (which, I have to say for the record, turned out to be too unbreathable to really work for the beach).
I
noticed the original boots were basically constructed of two halves
joined at the front and back, so I decided to use the same model for my
fabric covering. I traced the front line of one boot onto the chiffon,
cut it out, and repeated three times. I even remembered to reverse the
direction for the opposite half of each boot, but I don't think it
mattered because the front of this fabric looks the same as the back.
I
joined the two halves and sewed a seam down the front line of each. The
material was so sheer, that I had to temporarily glue the two halves
together and support them with a piece of paper while sewing.
Once
the paper was ripped off and the glue washed out, I started work with a
different kind of glue, to attach the fabric to the boots. Having had
decent success with Mod Podge outdoor glue on the last shoe project, I
used it again. I started by painting a thin layer of the glue onto the
left forefoot of the boot.
Starting
at the toe, I began fitting the fabric to the boot. I lined up the
center line of my fabric cover to the center line of the original boot,
then pressed the material down into the glue. I did not go very far,
because the chiffon was too thin to really grip the glue, and it kept
sliding around as I tried to stretch it to fit. So, once again, I found
myself gluing very small areas, then waiting an hour or so for them to
dry before moving on.
I
found this was much easier to do with the shoe actually on my foot, to
lend some support from the inside. On the first boot, I glued down a
significant portion of the left half of the foot before moving on to the
right. But on the second boot, I did the left and right halves at the
same time, which seemed to result in a smoother finish.
After
several days of this piecemeal gluing process, I had worked my way
completely up the boots' shafts. At this point, I decided to work on the bottom edges. I chose to make these shoes as "authentic" as possible, and tuck the fabric in between the uppers and soles. I pried the sole from the uppers, just around the
edges, with a screwdriver.
I used the same screwdriver to press the fabric into the gap, once I had filled it with E-6000, my most heavy-duty glue.
Now came a challenge: Finishing the
edge along the back zipper. To accomplish this, I folded the fabric to
the underside and pressed a crease into it with a flat iron.
Then,
I glued it down along the length of the zipper. This required the use
of copious numbers of binder clips to hold it all in place while it
dried.
While on the subject of clipping things, let's talk about the top edges! I flat-ironed
another crease into the very top half-inch of the fabric, and then folded them
over the boot tops to the inside, so that the raw edges were safely enclosed.
I discovered that the binder clips were causing indentations in the soft material, so I switched to clothespins halfway through.
When I had cut out the fabric, I'd left enough
for the heels to be in one piece with the uppers. But due to the way the
fabric had conformed to the shoes, the remaining material wasn't quite long enough. Since the original idea for the heels wouldn't work, I cut the fabric just below the line where the bottoms of the uppers meet the top of the heels.
Normally, the fabric for the uppers and heels are tucked into the gap between them, but since I couldn't actually remove the heels to create a space, I did the next best thing: sew a seam into the fabric. Because the uppers were already firmly glued on, there was no way I could machine-sew this seam, so I did it by hand.
Then I
wrapped the material around the heels and glued it down just as before,
doubling it over on the inside of the heel where it can't be seen.
At the very bottom of the heel, there was a nice big cavity where I tucked the remaining fabric. The taps popped right back in over this. And that was it!
Am I happy with the results? Mostly.
The
fabric really didn't want to stick down firmly, and sometimes it
puckered around folds and curves, so the texture is less smooth than I
would have hoped. However, the busy pattern mostly disguises these
flaws.
Awesome!
ReplyDeleteYou did a very good job. Thanks for sharing!
ReplyDelete